Get a quote
Free tool

Laser kerf and joint calculator

Measure how much material your laser burns away, then size slots, fingers and holes so parts fit the way you want.

1. Measure your kerf

2. Size your parts

Measure the sheet with a calliper
Fit

Draw slots this wide (no offset)

0

Measured kerf
0
Kerf offset in software
0
Draw fingers
0
Draw finger gaps
0
Outer part, no offset
0
Hole, no offset
0

"No offset" means cutting on the drawn line. With a kerf offset in your software, draw everything at its real size.

The kerf is the width of material the beam removes as it cuts, usually 0.1 to 0.3 mm on a CO2 laser and less on a fibre laser. Because half the kerf comes off each side of every line, outer parts come out slightly small and holes slightly big. On a box or a slot-together model that difference decides whether a joint is loose, snug or impossible to push together. Measure it once for each material and thickness, and you can design parts that fit the first time.

How to measure kerf with a strip test

Draw a rectangle 50 mm wide and about 20 mm high, and divide it into 10 strips with 9 vertical lines. Cut it at your normal settings. Push the strips tightly together and measure the total width with a vernier or digital calliper. Every cut removed one kerf, including half a kerf on each outer edge, so the kerf is the missing width divided by the number of strips. Enter the numbers in the first panel; the result fills in the second panel automatically.

Slots, fingers and press fits

If you cut without any kerf compensation, a slot drawn at width S comes out at S plus the kerf, and a finger drawn at width F comes out at F minus the kerf. To make a slot fit material of thickness T, draw it at T plus your clearance minus the kerf. For finger joints, draw the fingers one kerf wider and the gaps one kerf narrower. A press fit uses a small negative clearance (about 0.05 mm in MDF and plywood); acrylic is brittle and cracks, so use a snug or sliding fit there.

Kerf offset in software

Instead of redrawing, most laser software can offset the cut path. In LightBurn, use Kerf Offset in the cut settings and enter half the kerf: outer shapes move outwards and holes move inwards. Remember that plywood and MDF vary in thickness from sheet to sheet, often by 0.2 mm or more, so measure the actual sheet with a calliper rather than trusting the nominal 3 mm. If you order cut parts from a shop, tell them which edges need to fit together.

Frequently asked questions

What is a typical laser kerf?
On an 80 W CO2 laser with a 2 inch lens, around 0.15 to 0.2 mm in 3 mm plywood and MDF and 0.2 to 0.3 mm in 6 mm acrylic. Thicker material and a defocused beam give a wider kerf at the top than the bottom. Fibre lasers cutting thin steel are often 0.1 to 0.2 mm.
Does kerf change with thickness?
Yes. The beam is focused to a cone, so thicker material gives a wider kerf and a slightly tapered edge. Measure each thickness separately, and focus in the middle of thick material for straighter edges.
Why are my finger joints too loose?
The fingers lost half a kerf on each side and the gaps gained the same, so the joint is one full kerf looser than drawn. Add the kerf to each finger, or use your software's kerf offset, and check the real sheet thickness.
Can a laser shop compensate for kerf for me?
Yes. Say which parts must slot together and the material thickness, and a good shop will cut a test piece first. See wood laser cutting and acrylic laser cutting.

More free tools

Get a free laser quote

Fill in the job sheet: what you want made or bought, how many, the material and where you are. Laser shops, dealers and suppliers who work in your area quote you directly. Free, no obligation.

Job sheetReference number assigned when sent

Items

LineItem, size or modelQtyMaterialRemove
L1
L2
Up to 12 lines. Not sure of the quantity? Leave it empty.
Options

Free and no obligation. By sending you agree that we may share your request with a suitable laser shop, dealer or supplier. See our privacy policy.

Get a free quote