Get a quote
Free tool

Laser material compatibility guide

Search any material to see whether a CO2, diode or fibre laser can cut or engrave it, how thick it can go, and which plastics are dangerous.

Laser
MaterialCO2DiodeFibreSafety
Plywood and birch plyCuts to about 9 mm at 80 W. Glue lines vary, so buy laser-grade ply for clean cuts.Cut and engraveCut and engraveNoSafe
MDF and hardboardCuts cleanly with dark edges. Resin fumes: extraction essential.Cut and engraveCut and engraveNoVentilate
Solid wood and bambooEngraves beautifully; resinous pine flares. Hardwood cuts slower than ply.Cut and engraveCut and engraveNoSafe
Cast acrylic (Perspex)Flame-polished edge when cut; engraving comes out frosted white. Diodes only cut dark opaque colours.Cut and engraveNoNoVentilate
Extruded acrylicCheaper, cuts with a glossy edge, engraves less white than cast. Fumes smell strongly.Cut and engraveNoNoVentilate
Paper, card and cardboardLow power and air assist to avoid flare-ups. Great for invitations and packaging.Cut and engraveCut and engraveNoSafe
Vegetable-tanned leatherEngraves dark and cuts well. Smells strongly; ventilate.Cut and engraveCut and engraveNoVentilate
Chrome-tanned leatherContains chromium salts; engrave lightly with good extraction, avoid cutting.Engrave onlyEngrave onlyNoVentilate
Cotton, felt, denim and canvasCuts with sealed edges. Synthetic fabrics melt; check they are not PVC-coated.Cut and engraveCut and engraveNoSafe
CorkPopular for coasters. Engraves light brown.Cut and engraveCut and engraveNoSafe
Laser-safe rubberUse rubber sold for lasers only. Ordinary and neoprene rubber can contain chlorine.Cut and engraveEngrave onlyNoVentilate
Glass and crystalFrosted engraving with CO2; cannot be cut. 3D crystal uses a special green laser.Engrave onlyWith marking sprayNoSafe
Slate, granite and tileEngraves light on dark slate and granite. Great for photos and memorial plaques.Engrave onlyEngrave onlyEngrave onlySafe
Anodised aluminiumCO2 and diode remove the anodising for a white mark; fibre marks, engraves and (at kW) cuts.Engrave onlyEngrave onlyCut and engraveSafe
Powder-coated tumblers and metalThe coating is burnt off to show bright metal underneath.Engrave onlyEngrave onlyEngrave onlySafe
Stainless steelFibre marks, colours (MOPA) and cuts. CO2 and diode only with a marking spray.With marking sprayWith marking sprayCut and engraveSafe
Mild steelFibre cutting from 1 kW. Ear tags and serial plates are fibre-marked.With marking sprayWith marking sprayCut and engraveSafe
Brass, copper and silverVery reflective; needs a fibre laser, ideally with back-reflection protection for cutting.NoNoCut and engraveSafe
Polypropylene (PP)Thin sheet cuts but melts at the edge. Test first.Cut and engraveNoNoVentilate
Polycarbonate (Lexan)Burns and yellows; only very thin film cuts. Use acrylic instead.NoNoNoVentilate
ABSMelts into a mess and gives off hydrogen cyanide.NoNoNoNever
HDPE and polystyrene foamMelts and catches fire easily.NoNoNoNever
PVC, vinyl and faux leatherReleases chlorine gas: toxic, and it corrodes the machine. Never laser it.NoNoNoNever
PTFE (Teflon)Releases toxic fluorine compounds.NoNoNoNever
Fibreglass and carbon fibreToxic resin fumes and harmful fibre dust.NoNoNoNever

Not every material belongs in a laser. Wood, acrylic, leather, card and anodised aluminium cut or engrave beautifully; PVC, vinyl and some other plastics release toxic, corrosive gases that harm you and destroy the machine. Which laser you have matters too: a CO2 laser cuts wood and acrylic but only marks bare metal with a coating, a fibre laser marks metal but passes through clear acrylic and glass, and a diode laser cannot cut clear or blue acrylic at all. Filter the guide by laser type or search for your material.

Cutting thickness by laser power

The table below gives rough maximum thicknesses for a clean, single-pass cut with air assist on a well-aligned machine. Multiple passes can go thicker, with more charring and a tapered edge. Fibre cutting figures are for oxygen-assisted mild steel and nitrogen-assisted stainless steel and aluminium.

CO2 laserPlywoodMDFAcrylic
40 W4 mm4 mm5 mm
60 W6 mm6 mm8 mm
80 W9 mm9 mm12 mm
100 W12 mm12 mm15 mm
130 to 150 W15 to 18 mm15 to 18 mm20 to 25 mm
Fibre laserMild steelStainlessAluminium
1 kW8 mm3 mm2 mm
1.5 kW12 mm5 mm4 mm
3 kW20 mm10 mm8 mm
6 kW25 mm20 mm16 mm

Diode lasers of 10 to 20 W optical power cut plywood and MDF up to about 3 to 6 mm in several passes, and dark acrylic up to about 3 mm.

How to check an unknown plastic

If you are not sure what a plastic is, do not put it in the laser. Ask the supplier for the data sheet. A quick test for PVC is the copper wire test: heat a clean copper wire in a flame, touch it to the plastic and put it back in the flame; a green flame means chlorine, so it is PVC or another chlorinated plastic. Faux leather, vinyl wrap, many rubber stamps, cable insulation and some foam boards contain PVC. Laser-safe rubber and laser-safe vinyl are sold specifically for lasers.

Safety and extraction

Every material makes smoke, and some make it worse: MDF and plywood glues, leather, and acrylic all give off fumes you should not breathe, so vent to the outside or use a filter rated for laser fumes. Never leave a laser running unattended, keep a CO2 fire extinguisher next to it and keep the honeycomb bed clean. Wear safety glasses for your laser's wavelength (10,600 nm for CO2, 1,064 nm for fibre, about 450 nm for blue diodes) with open-frame machines. A laser technician can service extraction and alignment.

Frequently asked questions

Which plastics can I never laser cut?
PVC and vinyl (chlorine gas), polycarbonate thicker than about 1 mm (burns and yellows), ABS (melts and gives off hydrogen cyanide), PTFE or Teflon (fluorine compounds), and fibreglass or carbon fibre (toxic resin fumes and dust). Avoid any plastic you cannot identify.
Can a diode laser cut acrylic?
Only dark, opaque acrylic, slowly and in several passes. Clear, white and blue acrylic let blue diode light pass through or reflect it, so it does not cut. A CO2 laser cuts all colours of acrylic with a polished edge.
Can a CO2 laser engrave metal?
It engraves anodised aluminium and painted or powder-coated metal by removing the coating. On bare stainless steel it needs a marking spray or paste. For direct metal marking and deep engraving, use a fibre laser.
Is MDF safe to laser?
Yes, with good extraction. MDF is bonded with resins that give off formaldehyde and smoke when cut, and the edges come out dark brown. Moisture-resistant and fire-retardant MDF can cut differently, so test first.

More free tools

Get a free laser quote

Fill in the job sheet: what you want made or bought, how many, the material and where you are. Laser shops, dealers and suppliers who work in your area quote you directly. Free, no obligation.

Job sheetReference number assigned when sent

Items

LineItem, size or modelQtyMaterialRemove
L1
L2
Up to 12 lines. Not sure of the quantity? Leave it empty.
Options

Free and no obligation. By sending you agree that we may share your request with a suitable laser shop, dealer or supplier. See our privacy policy.

Get a free quote